Flatbed wrecker truck operation steps:
1. Disengage the winch clutch, pull out the cable to the vehicle to be carried before the "j" line hook was hooked on the lower part of the vehicle was dragged traction hook
shackle. The winch clutch is then engaged.
Note: When pulling out the cable, the number of the remaining cable can not be less than 5 turns
2. The vehicle is parked by neutral, and the parking brake of the vehicle being carried is released.
3. control the winch joystick, the car on the platform, and control the j-hook on the wire from the winch is greater than 0.4m
Note: When the winch by the load, do not manually disconnect the winch clutch control! . This will damage the winch.
Note: When using the chain hook to use the winch traction accident car, especially the chassis than the end of the car, be very careful not to damage the trailer parts, so as
not to cause unnecessary trouble.
4. When the loaded vehicle has been dragged in place, tied with a safety strap rear tires, the car will be loaded on both sides of the rear obliquely stretched fixed on both
sides of the flat ring. NOTE: If the safety tab is broken, the safety straps should be wrapped around the sturdy parts of the car. For a safety bandage that can not be manually
locked, the official winch joystick controls the winch to move the loader a little forward so that the safety chain is properly tensioned.
5 flat belt with a fixed fault car, you must have four straps to be locked in the wheel or body.
6. Tighten the strap with the ratchet must be in a closed state.
Note! . : Nylon strap for a long time there will be tension loose phenomenon, the operation should be regularly checked bandage tension, especially in poor road conditions or
more brakes more cases, should be promptly inspected for fastening, to avoid accidents.
7. Control platform tilt joystick, the platform tail raised 0.15m from the ground.
8. Control Platform Tilt the joystick to move the platform forward approximately 0.6 m from the front. The control platform tilts the joystick to return the platform to the
horizontal position.
9. Control Platform Slide the joystick to move the platform forward to the front.
10. In order to prevent the next driving process, due to vibration, rope tension on the winch may cause damage, you must use the other two safety chain in accordance with the
aforementioned method of fixing the front of the car, and try to tension. Load positioning and tension.
11. Will be mounted car hanging a file, pull handbrake.
12. Check that all safety chains or chain belts and connections are secure and tight.
13. Following the completion of the above steps, ie, follow-up procedures. Depress the wrecker truck clutch, remove the power take-off, platform loading operation is complete.
Hubei Changjie Special Purpose Vehicle Co. Ltd
Contact Name: Mr. Suan Yin
E-mail: cj802@urspv.com
Mobile phone: +8613886881673
Tel: +(00)867223229933
1. Disengage the winch clutch, pull out the cable to the vehicle to be carried before the "j" line hook was hooked on the lower part of the vehicle was dragged traction hook
shackle. The winch clutch is then engaged.
Note: When pulling out the cable, the number of the remaining cable can not be less than 5 turns
2. The vehicle is parked by neutral, and the parking brake of the vehicle being carried is released.
3. control the winch joystick, the car on the platform, and control the j-hook on the wire from the winch is greater than 0.4m
Note: When the winch by the load, do not manually disconnect the winch clutch control! . This will damage the winch.
Note: When using the chain hook to use the winch traction accident car, especially the chassis than the end of the car, be very careful not to damage the trailer parts, so as
not to cause unnecessary trouble.
4. When the loaded vehicle has been dragged in place, tied with a safety strap rear tires, the car will be loaded on both sides of the rear obliquely stretched fixed on both
sides of the flat ring. NOTE: If the safety tab is broken, the safety straps should be wrapped around the sturdy parts of the car. For a safety bandage that can not be manually
locked, the official winch joystick controls the winch to move the loader a little forward so that the safety chain is properly tensioned.
5 flat belt with a fixed fault car, you must have four straps to be locked in the wheel or body.
6. Tighten the strap with the ratchet must be in a closed state.
Note! . : Nylon strap for a long time there will be tension loose phenomenon, the operation should be regularly checked bandage tension, especially in poor road conditions or
more brakes more cases, should be promptly inspected for fastening, to avoid accidents.
7. Control platform tilt joystick, the platform tail raised 0.15m from the ground.
8. Control Platform Tilt the joystick to move the platform forward approximately 0.6 m from the front. The control platform tilts the joystick to return the platform to the
horizontal position.
9. Control Platform Slide the joystick to move the platform forward to the front.
10. In order to prevent the next driving process, due to vibration, rope tension on the winch may cause damage, you must use the other two safety chain in accordance with the
aforementioned method of fixing the front of the car, and try to tension. Load positioning and tension.
11. Will be mounted car hanging a file, pull handbrake.
12. Check that all safety chains or chain belts and connections are secure and tight.
13. Following the completion of the above steps, ie, follow-up procedures. Depress the wrecker truck clutch, remove the power take-off, platform loading operation is complete.
Hubei Changjie Special Purpose Vehicle Co. Ltd
Contact Name: Mr. Suan Yin
E-mail: cj802@urspv.com
Mobile phone: +8613886881673
Tel: +(00)867223229933
